Sharpening Stones
Poltava Diamond and cubic boron nitride (CBN, borazon, cubonite, elbor) sharpening and honing stones. |
CBN (CUBIC BORON NITRIDE, BORAZON) SHARPENING STONES, METAL AND COMBINED BONDS, CONCENTRATION 100%, NARROW
150-12-7-4-3
Length: 150 mm = 6 inch
Width: 12 mm = 0.5 inch
CBN height: 3 mm = 0.12 inch
Total height (with blank): 7 mm = 0.28 inch
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bonds: Metal M2-01 (copper-tin), Combined (copper-resin, depending on grain size)
Flat solid block on aluminum blank.
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON = MESH(GRIT) = FEPA
Grain concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Available on stock
Application
For sharpening of curved blades using such sharpeners as Hapstone, Edge Pro, Kazak Pro.
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 year), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in grain selection window. I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
HONING, SHARPENING STONES
200-30-8-3-5
CBN (cubic boron nitride) is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor, cubonite, etc.
CBN (cubic boron nitride) is the second-hardest material after diamond, and has the best price-performance ratio for processing steels, comparing to other materials, including diamond, silicon carbide or aluminum oxide.
Due to it's high resistance specs, CBN can be used dry without lubricant. This makes CBN the cleanest of the available sharpening stones.
Length: 200 mm = 7.9 inch
Width: 30 mm = 1.2 inch
Total thickness: 8 mm = 0.32 inch
CBN thickness: 3 mm = 0.12 inch
Blank thickness: 5 mm = 0.2 inch
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bond: innovative combined bonds to ensure the best performance, resin bond BP50 for polishing at fine sizes and metal-resin bond BP05 for grinding at coarser grain sizes.
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON=MESH(GRIT)=FEPA
CBN concentration: 100%
Flat solid block on aluminum blank.
Available on stock
Preparation of sharpening stones
Unlike other sharpening stones, most of these combined bond stones do not need preparation, except stones with grits finer 1 microns (<Grit 15000). Ultrafine grains (1/0, 0.5/0) form agglomerates in a bond, so you may need to dress them with abrasive powders/pastes, or they will be self-polished after sharpening of 30-50 knives.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 years), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in dimensions selection window (click also any grain size to select it). I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Knife sharpening with CBN combined bond stones
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
SHARPENING STONES
150 х 35 х 7 x 3 x 4
CBN (cubic boron nitride) is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor, cubonite, etc.
CBN (cubic boron nitride) is the second-hardest material after diamond, and has the best price-performance ratio for processing steels, comparing to other materials, including diamond, silicon carbide or aluminum oxide.
Due to it's high resistance specs, CBN can be used dry without lubricant. This makes CBN the cleanest of the available sharpening stones.
Length: 150 mm = 6 inch
Width: 35 mm = 1.4 inch
Total thickness: 7 mm = 0.28 inch
CBN thickness: 3 mm = 0.12 inch
Blank thickness: 4 mm = 0.16 inch
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bond: innovative combined bonds to ensure the best performance, resin bond BP50 for polishing at fine sizes and metal-resin bond BP05 for grinding at coarser grain sizes.
Use of lubricant is not mandatory, but recommended.
You may find lubricant here
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON=MESH(GRIT)=FEPA
CBN concentration: 100%
Flat solid block on aluminum.
Available on stock
Preparation of sharpening stones
Unlike other sharpening stones, most of these combined bond stones do not need preparation, except stones with grits finer 1 microns (<Grit 15000). Ultrafine grains (1/0, 0.5/0) form agglomerates in a bond, so you may need to dress them with abrasive powders/pastes, or they will be self-polished after sharpening of 30-50 knives.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 years), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Knife sharpening with CBN combined bond stones
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
RECOMMENDED SETS OF DIAMOND AND CBN STONES, METALL AND COMBINED BONDS
Recommended selections of sharpening stones to make your choice easier:
- Highlight your operations: do you have "forming cutting edge" operation ? What surface quality do you need, just "nice at eyesight" (polishing) or mirror (the finest polishing). So skip sets with unnecessary grains.
- What is your workload ? If from time to time - skip metal bond stones, they are more expensive, but lasts longer.
- CBN combined bond stones are recommended for all types of steels;
- The more knives you sharpen, the more you need stones, to keep steps in working operations (distances between grain sizes) shorter.
Diamond stone 150x25x7x3, combined bond, grain size 200/160 - forming the cutting edge
Diamond stone 150x25x7x3, combined bond, grain size 100/80 - rough sharpening
Diamond stone 150x25x7x3, combined bond, grain size 40/28 - fine sharpening
Diamond stone 150x25x7x3, combined bond, grain size 20/14 - fine lapping
Diamond stone 150x25x7x3, combined bond, grain size 7/5 - the finest lapping
Diamond stone 150x25x7x3, combined bond, grain size 3/2 - polishing.Diamond stone 150x25x7x3, combined bond, grain size 200/160 - forming the cutting edge
Diamond stone 150x25x7x3, combined bond, grain size 100/80 - rough sharpening
Diamond stone 150x25x7x3, combined bond, grain size 40/28 - fine sharpening
Diamond stone 150x25x7x3, combined bond, grain size 20/14 - fine lapping
Diamond stone 150x25x7x3, combined bond, grain size 7/5 - the finest lapping
Diamond stone 150x25x7x3, combined bond, grain size 3/2 - polishing.
Diamond stone 150x25x7x3, combined bond, grain size 1/0 - fine polishing.
Diamond stone 150x25x7x3, combined bond, grain size 0.25 / 0 - the finest polishing.Diamond stone 150x25x7x3, combined bond, grain size 200/160 - forming the cutting edge
Diamond stone 150x25x7x3, combined bond, grain size 125/100 - rough sharpening
Diamond stone 150x25x7x3, combined bond, grain size 63/50 - semi-finishing
Diamond stone 150x25x7x3, combined bond, grain size 28/20 - fine sharpening
Diamond stone 150x25x7x3, combined bond, grain size 14/10 - fine lapping
Diamond stone 150x25x7x3, combined bond, grain size 7/5 - the finest lapping
Diamond stone 150x25x7x3, combined bond, grain size 3/2 - polishing.Diamond stone 150x25x7x3, combined bond, grain size 200/160 - forming the cutting edge
Diamond stone 150x25x7x3, combined bond, grain size 125/100 - rough sharpening
Diamond stone 150x25x7x3, combined bond, grain size 63/50 - semi-finishing
Diamond stone 150x25x7x3, combined bond, grain size 28/20 - fine sharpening
Diamond stone 150x25x7x3, combined bond, grain size 14/10 - fine lapping
Diamond stone 150x25x7x3, combined bond, grain size 5/3 - polishing
Diamond stone 150x25x7x3, combined bond, grain size 2/1 - fine polishing.
Diamond stone 150x25x7x3, combined bond, grain size 0.5 / 0 - the finest polishing.Diamond stone 150x25x7x3, combined bond, grain size 100/80 - rough sharpening
Diamond stone 150x25x7x3, combined bond, grain size 40/28 - fine sharpening
Diamond stone 150x25x7x3, combined bond, grain size 20/14 - fine lapping
Diamond stone 150x25x7x3, combined bond, grain size 7/5 - the finest lappingDiamond stone 150x25x7x3, combined bond, grain size 125/100 - rough sharpening
Diamond stone 150x25x7x3, combined bond, grain size 63/50 - semi-finishing
Diamond stone 150x25x7x3, combined bond, grain size 28/20 - fine sharpening
Diamond stone 150x25x7x3, combined bond, grain size 14/10 - fine lapping
Diamond stone 150x25x7x3, combined bond, grain size 7/5 - the finest lappingDiamond stone 150x25x3, metal bond, 100%, grain size 160/125 - rough sharpening
Diamond stone 150x25x3, metal bond, 100%, grain size 80/63 - semi-finishing
Diamond stone 150x25x3, metal bond, 100% ,grain size 40/28 - fine sharpening
Diamond stone 150x25x3, metal bond, 100%, grain size 20/14 - fine lapping
Diamond stone 150x25x3, metal bond, 100%, grain size 10/7 - the finest lapping
Diamond stone 150x25x3, metal bond, 100%, grain size 5/3 - polishing.Recommended set # 8:
CBN stone 150x25x3, metal bond, grain size 200/160 - forming the cutting edge
CBN stone 150x25x3, metal bond, grain size 100/80 - rough sharpening
CBN stone 150x25x3, metal bond, grain size 40/28 - fine sharpening
CBN stone 150x25x7x3 combined bond, grain size 20/14 - fine lapping
CBN stone 150x25x7x3 combined bond, grain size 10/7 - the finest finishing
CBN stone 150x25x7x3 combined bond, grain size 5/3 - polishing
CBN stone 150x25x7x3 combined bond, grain size 2/1 - fine polishing.Recommended set # 9:
CBN stone 150x25x3, metal bond, grain size 200/160 - forming the cutting edge
CBN stone 150x25x3, metal bond, grain size 100/80 - rough sharpening
CBN stone 150x25x3, metal bond, grain size 40/28 - fine sharpening
CBN stone 150x25x7x3 combined bond, grain size 20/14 - fine lapping
CBN stone 150x25x7x3 combined bond, grain size 10/7 - the finest finishing
CBN stone 150x25x7x3 combined bond, grain size 5/3 - polishing
CBN stone 150x25x7x3 combined bond, grain size 2/1 - fine polishing.
CBN stone 150x25x7x3, combined bond, grain size 0.5 / 0 - the finest polishing.Recommended set # 10:
CBN stone 150x25x3, metal bond, grain size 200/160 - forming the cutting edge
CBN stone 150x25x3, metal bond, grain size 100/80 - rough sharpening
CBN stone 150x25x3, metal bond, grain size 40/28 - fine sharpening
CBN stone 150x25x7x3 combined bond, grain size 20/14 - fine lapping
CBN stone 150x25x7x3 combined bond, grain size 7/5 - the finest finishing
CBN stone 150x25x7x3 combined bond, grain size 3/2 - polishingRecommended set # 11:
CBN stone 150x25x3, metal bond, grain size 200/160 - forming the cutting edge
CBN stone 150x25x3, metal bond, grain size 100/80 - rough sharpening
CBN stone 150x25x3, metal bond, grain size 40/28 - fine sharpening
CBN stone 150x25x7x3, combined bond, grain size 20/14 - fine lapping
CBN stone 150x25x7x3, combined bond 7/5 grain size - the finest finishing
CBN stone 150x25x7x3, combined bond 3/2 grain size - polishing
CBN stone 150x25x7x3, combined bond, grain size 1/0 - fine polishing.Recommended set # 12:
CBN stone 150x25x3, metal bond, grain size 200/160 - forming the cutting edge
CBN stone 150x25x3, metal bond, grain size 125/100 - rough sharpening
CBN stone 150х25х3, metal bond, , grain size 63/50 - semi-finish sharpening
CBN stone 150x25x3, metal bond, grain size 28/20 - fine finishing
CBN stone 150x25x7x3, combined bond, grain size 14/10 - fine lapping
CBN stone 150x25x7x3, combined bond, grain size 7/5 - the finest finishing
CBN stone 150x25x7x3, combined bond, grain size 3/2 - polishing.Recommended set # 13:
CBN stone 150x25x3, metal bond, grain size 125/100 - rough sharpening
CBN stone 150х25х3, metal bond, grain size 63/50 - semi-finish sharpening
CBN stone 150x25x3, metal bond, grain size 28/20 - fine finishing
CBN stone 150x25x7x3, combined bond, grain size 14/10 - fine lapping
CBN stone 150x25x7x3, combined bond grain size 7/5 - the finest finishingRecommended set # 14:
CBN stone 150x25x3, metal bond, grain size 100/80 - rough sharpening
CBN stone 150x25x3, metal bond, grain size 40/28 - fine sharpening
CBN stone 150x25x7x3, combined bond, grain size 20/14 - fine lapping
CBN stone 150x25x7x3, combined bond, grain size 10/7 - the finest finishing
Recommended set # 15:
CBN stone 150x25x7x3, combined bond, grain size 125/80 - rough sharpening
CBN stone 150x25x7x3, combined bond, grain size 63/50 - semi-finish sharpening
CBN stone 150x25x7x3, combined bond, grain size 28/20 - fine finishing
CBN stone 150x25x7x3, combined bond, grain size 14/10 - fine lapping
CBN stone 150x25x7x3, combined bond, grain size 7/5 - the finest finishing
Recommended set # 16:
CBN stone 150x25x7x3, combined bond, grain size 200/160 - forming the cutting edge
CBN stone 150x25x7x3, combined bond, grain size 125/100 - rough sharpening
CBN stone 150x25x7x3, combined bond, grain size 63/50 - semi-finish sharpening
CBN stone 150x25x7x3, combined bond, grain size 28/20 - fine finishing
CBN stone 150x25x7x3, combined bond, grain size 14/10 - fine lapping
CBN stone 150x25x7x3, combined bond, grain size 7/5 - the finest finishing
CBN stone 150x25x7x3, combined bond, grain size 3/2 - polishing.Recommended set # 17:
CBN stone 150x25x3, metal bond, grain size 200/160 - forming the cutting edge
CBN stone 150x25x3, metal bond, grain size 100/80 - rough sharpening
CBN stone 150x25x3, metal bond, grain size 40/28 - fine sharpening
CBN stone 150x25x7x3, combined bond, grain size 20/14 - fine lapping
CBN stone 150x25x7x3, combined bond, grain size 7/5 - the finest finishing
CBN stone 150x25x7x3, combined bond, grain size 3/2 - polishing
CBN stone 150x25x7x3, combined bond, grain size 1/0 - fine polishing.
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bonds
Metal bond: M2-01, copper-tin
Combined bond: composition depends on grain size, does not require cooling, but you may use water (or water based cooling liquids) as lubricant.
Grain size: Please select from the list, or read Technical information.The finest grain size is 0.5/0 micron (fine polishing) , the coarsest - 200/160 micron (rough grinding).
In grain selection window you see grain sizes according to standards:
MICRON = MESH(GRIT) = FEPA
Grain concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Available on stock
Application
For knife sharpening using such sharpeners as Hapstone, Edge Pro. etc.
Preparation of sharpening stones
Stones with grits finer 3 microns may require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
Selection of SiC powders for dressing of sharpening stones
Stone Starting grit Finishing grit 500/400 μ = 35/40= D501 F16 (1230 μ) F24 (745 μ) 400/315 μ = 40/45= D426 F16 (1230 μ) F46 (370 μ) 315/250 μ = 50/60= D301 F24 (745 μ) F46 (370 μ) 250/200 μ = 60/70= D251 F24 (745 μ) F60 (260 μ) 200/160 μ = 70/80= D213 F36 (525 μ) F60 (260 μ) 160/125 μ = 100/120= D151 F46 (370 μ) F80 (180 μ) 125/100 μ = 120/140= D126 F60 (260 μ) F100 (129 μ) 100/80 μ = 140/170= D107 F60 (260 μ) F120 (109 μ) 80/63 μ = 170/200= D91 F80 (180 μ) F150 (82 μ) 63/50 μ = 230/270= D64 F100 (129 μ) F180 (69 μ) 50/40 μ = 270/325= D54 F120 (109 μ) F220 (58 μ) 40/28 μ = 550= M40 F150 (82 μ) F240 (46 μ) 28/20 μ = 650= M25 F180 (69 μ) F320 (30 μ) 20/14 μ = 1100= M20 F240 (46 μ) F400 (18 μ) 14/10 μ = 1500= M16 F320 (30 μ) F400 (18 μ) 10/7 μ = 1700= M10 F400 (18 μ) F600 (10 μ) 7/5 μ = 3000= M6.3 F600 (10 μ) F800 (6,7 μ) 5/3 μ = 4000= M4 F600 (10 μ) F800 (6,7 μ) 3/2 μ = 6000= M1.5 F800 (6,7 μ) F1200 (3 μ) 2/1 μ = 10000 F800 (6,7 μ) F1200 (3 μ) 1/0 μ F800 (6,7 μ) F1200 (3 μ) 0.5/0 μ F800 (6,7 μ) F1200 (3 μ)
Use and cleaning of sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 years), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
- 10 mins setting in 25% mixture (25 gr FeCl per 75 gr of water),
- 10 mins polish movements (carefully draw "8") on glass plate.
Free shipping
Contact us for combined shipping quote or bulk discounts.
Please read more about:Shipping
Warranty, returns and refunds
Grain size conversion, selection and use of your tool
Length: 150 mm = 6 inch
Width: 12 mm = 0.5 inch
CBN thickness: 3 mm = 0.12 inch
Blank thickness: 4 mm = 0.16 inch
Total thickness: 7 mm = 0.28 inch
Application: For sharpening of curved (S-shaped) blades
Buy all necessary stones and save: 10%!
These next generation stones were developed on the basis of our experience in sharpening business:
- solid support plate (thicker aluminum blank: 4 mm vs. competitors' 3 mm);
- appropriate bonds (selected, depending on grain size)
- combination of long life, delicate sharpening, and excellent performance of combined(metal-resin) bonds.
Concentration 100%.
Flat solid block on aluminum blank, grains are distributed evenly across the stone.
Material: CBN - cubic boron nitride. It has the best cost/productivity ratio for processing of steels, comparing to diamond and cheaper stones, they are similar in qualities to Japanese wet stones, but have ten times longer working life. CBN is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor.
Sharpening stones in sets (grain size format: Micron(UA) = ANSI(US) = FEPA(EU)
Set of 4 stones:
1. 100/80μ = 140/170 = D107, metal bond M2-01 - rough sharpening
2. 50/40μ = 270/325 = D54, combined (metal-resin) bond BP50 - fine sharpening
3. 20/14μ = 1100 = M20, combined (metal-resin) bond BP50 - polishing
4. 7/5μ = 3000 = M6.3, combined (metal-resin) bond BP50 - polishing
Set of 5 stones:
1. 100/80μ = 140/170 = D107, metal bond M2-01 - rough sharpening
2. 50/40μ = 270/325 = D54, metal bond - sharpening
3. 28/20μ = 650 = M25, combined (metal-resin) bond BP50 - polishing
4. 14/10μ = 1500 = M16, combined (metal-resin) bond BP50 - polishing
5. 7/5μ = 3000 = M6.3, combined (metal-resin) bond BP50 - polishing
Set of 6 stones:
1. 160/125μ = 100/120 = D151, metal bond M2-01 - rough sharpening
2. 80/63μ = 170/200 = D91, metal bond - sharpening
3. 40/28μ = 550 = M40, combined (metal-resin) bond BP50 - polishing
4. 20/14μ = 1100 = M20, combined (metal-resin) bond BP50 - polishing
5. 10/7μ = 1700 = M10, combined (metal-resin) bond BP50 - polishing
6. 5/3μ = 4000 = M4, combined (metal-resin) bond BP50 - polishing
Recommendations on selection of sharpening stones.
How to maintain sharpening stones
Download full catalog
Grain size/operation reference chart
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Knife sharpening with CBN combined bond stones
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
150-25-5-2mm / 6''-1''-0.2''-0.08''
WE STOPPED PRODUCTION OF THESE STONES AND OFFER INNOVATIVE CBN STONES WITH COMBINED BOND: BETTER PERFORMANCE, LONGER TOOL LIFE AND LOWER COSTS.
We offer stock of these stones (100% and 200%) for SALE: 70pcs of each grain size (0.5/0 - 200/160).
Yet, we still continue maintaining some stock of these resin bond CBN stones.
CBN (cubic boron nitride) is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor, cubonite, etc.
CBN (cubic boron nitride) is the second-hardest material after diamond, and has the best price-performance ratio for processing steels, comparing to other materials, including diamond, silicon carbide or aluminum oxide.
Due to it's high resistance specs, CBN can be used dry without lubricant. This makes CBN the cleanest of the available sharpening stones.
Length: 150 mm = 6 inch
Width: 25 mm = 1 inch
CBN height: 2 mm = 0.08 inch - comparing with 3 mm of new stones
Total height (with blank): 5 mm = 0.2 inch - comparing with 7 mm of new stones
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Special resin bond BN-130, does not require cooling, but you may use water (or water based cooling liquids) as lubricant.
Metal bond on order
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON = MESH(GRIT) = FEPA
Grain concentration: 100% and 200%
Flat solid block on aluminum blank.
Available on stock
Application
For knife sharpening using such sharpeners as Hapstone or Edge Pro.
Preparation of sharpening stones
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 year), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in grain selection window. I sell it if you buy a stone.
Reference chart
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
STARTER PACKS OF DIAMOND AND CBN SHARPENING STONES, RESIN AND METAL BONDS
Low cost, but premium quality solution for novice sharpener. Blank is thinner, edges are not beveled, modest packaging, stones need preparation.
Length: 150 mm = 6 inch
Width: 25 mm = 1 inch
CBN height: 3 mm = 0.1 inch
Total height (with blank): 6 mm = 0.2 inch
Starter pack # 1, 3 CBN stones, resin bond50/40μ = 270/325 = D54 - fine grinding
20/14μ = 1100 = M20 - polishing
7/5μ = 3000 = M6.3 - polishing
Starter pack # 2, 4 CBN stones, metal and resin bond100/80μ = 140/170 = D107, metal bond - fine grinding
50/40μ = 270/325 = D54, resin bond - fine grinding
20/14μ = 1100 = M20, resin bond - polishing
7/5μ = 3000 = M6.3, resin bond - polishing
Starter pack # 3, 5 CBN stones, metal and resin bond100/80μ = 140/170 = D107, metal bond- fine grinding
50/40μ = 270/325 = D54 - fine grinding
20/14μ = 1100 = M20, resin bond - polishing
10/7μ = 1700 = M10, resin bond - polishing
5/3μ = 4000 = M4, resin bond - polishingStarter pack # 4, 6 CBN stones, metal and resin bond
200/160μ = 70/80 = D213, metal bond- sharpening / rough grinding
100/80μ = 140/170 = D107, metal bond - fine grinding
50/40μ = 270/325 = D54, resin bond - fine grinding
20/14μ = 1100 = M20, resin bond - polishing
10/7μ = 1700 = M10, resin bond - polishing
5/3μ = 4000 = M4, resin bond - polishingStarter pack # 5, 3 Diamond stones, resin bond
50/40μ = 270/325 = D54 - fine grinding
20/14μ = 1100 = M20 - polishing
7/5μ = 3000 = M6.3 - polishingStarter pack # 6, 4 Diamond stones, resin bond
100/80μ = 140/170 = D107 - fine grinding
50/40μ = 270/325 = D54 - fine grinding
20/14μ = 1100 = M20 - polishing
7/5μ = 3000 = M6.3 - polishingStarter pack # 7, 4 Diamond and CBN stones, metal and resin bond
100/80μ = 140/170 = D107, CBN, metal bond - fine grinding
50/40μ = 270/325 = D54, diamond, resin bond - fine grinding
20/14μ = 1100 = M20, diamond, resin bond - polishing
7/5μ = 3000 = M6.3, diamond, resin bond - polishingStarter pack # 8, 5 CBN and diamond stones, metal and resin bonds
100/80μ = 140/170 = D107, CBN, metal bond - fine grinding
50/40μ = 270/325 = D54, resin bond - fine grinding
20/14μ = 1100 = M20, diamond, resin bond - polishing
10/7μ = 1700 = M10, diamond, resin bond - polishing
5/3μ = 4000 = M4, diamond, resin bond - polishingStarter pack # 9, 6 CBN stones, metal and resin bond
200/160μ = 70/80 = D213, CBN, metal bond- sharpening / rough grinding
100/80μ = 140/170 = D107, CBN, metal bond - fine grinding
50/40μ = 270/325 = D54, diamond, resin bond - fine grinding
20/14μ = 1100 = M20, diamond, resin bond - polishing
10/7μ = 1700 = M10, diamond, resin bond - polishing
5/3μ = 4000 = M4, diamond, resin bond - polishingRecommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bonds:
Resin bond: phenol-formaldehyde, does not require lubricant, but you may use water (or water based cooling liquids)
Metal bond: M2-01, copper-tin
Grain size: Please select from the list, or read Technical information.The finest grain size is 0.5/0 micron (fine polishing) , the coarsest - 200/160 micron (rough grinding).
In grain selection window you see grain sizes according to standards:
MICRON = MESH(GRIT) = FEPA
Available on stock
Preparation of sharpening stones
These stones require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
Selection of SiC powders for dressing of sharpening stones
Stone Starting grit Finishing grit 500/400 μ = 35/40= D501 F16 (1230 μ) F24 (745 μ) 400/315 μ = 40/45= D426 F16 (1230 μ) F46 (370 μ) 315/250 μ = 50/60= D301 F24 (745 μ) F46 (370 μ) 250/200 μ = 60/70= D251 F24 (745 μ) F60 (260 μ) 200/160 μ = 70/80= D213 F36 (525 μ) F60 (260 μ) 160/125 μ = 100/120= D151 F46 (370 μ) F80 (180 μ) 125/100 μ = 120/140= D126 F60 (260 μ) F100 (129 μ) 100/80 μ = 140/170= D107 F60 (260 μ) F120 (109 μ) 80/63 μ = 170/200= D91 F80 (180 μ) F150 (82 μ) 63/50 μ = 230/270= D64 F100 (129 μ) F180 (69 μ) 50/40 μ = 270/325= D54 F120 (109 μ) F220 (58 μ) 40/28 μ = 550= M40 F150 (82 μ) F240 (46 μ) 28/20 μ = 650= M25 F180 (69 μ) F320 (30 μ) 20/14 μ = 1100= M20 F240 (46 μ) F400 (18 μ) 14/10 μ = 1500= M16 F320 (30 μ) F400 (18 μ) 10/7 μ = 1700= M10 F400 (18 μ) F600 (10 μ) 7/5 μ = 3000= M6.3 F600 (10 μ) F800 (6,7 μ) 5/3 μ = 4000= M4 F600 (10 μ) F800 (6,7 μ) 3/2 μ = 6000= M1.5 F800 (6,7 μ) F1200 (3 μ) 2/1 μ = 10000 F800 (6,7 μ) F1200 (3 μ) 1/0 μ F800 (6,7 μ) F1200 (3 μ) 0.5/0 μ F800 (6,7 μ) F1200 (3 μ)
Use and cleaning of sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 years), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
- 10 mins setting in 25% mixture (25 gr FeCl per 75 gr of water),
- 10 mins polish movements (carefully draw "8") on glass plate.
You may buy 100 gr. of FeCl in grain selection window. I sell it if you buy a stone.
Free shipping
Contact us for combined shipping quote or bulk discounts.
Please read more about:Shipping
Warranty, returns and refunds
Grain size conversion, selection and use of your tool
Length: 100, 125, 150, 200 mm
Width: 8, 12, 25, 40 mm
Height: 3, 4, 5 mm
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Metal bond, ensures high endurance and low wearing rate, may require lubricant
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON=MESH(GRIT)=FEPA
200-70-3 (only 500/400) and 150-25-3 (only 500/400) are stones with grain size 500/400μ = 35/40 = D501, this grain size is available only for 2 those stones.
Diamond concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Flat solid block, diamonds are distributed evenly across the stone.
You may also buy aluminum blank separately, if you buy stone.
How to attach stone to blank.
Available on stock
Preparation of sharpening stones
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of diamond sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance is only needed every year or two.
In 1-2 years you may need to flatten stone, 20 mins with Ferric chloride (FeCl):
- 10 mins setting in 25% mixture (25 gr FeCl per 75 gr of water),
- 10 mins polish movements (carefully draw "8") on glass plate.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in dimensions selection window (click also any grain size to select it). I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
- high hardness
- high temperatures resistance
- chemical resistance to components of alloys and steels.
Please select required dimensions and grain sizes from list.
Application: Accurate machining of holes and workpieces of cast iron, steel and other materials.
Download full catalog
Metal bond M2-01 (copper-tin)
CBN concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Flat solid block
Use and cleaning of sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
GIFT BOX: CBN, BORAZON, CUBIC BORON NITRIDE
SHARPENING STONES
12 sharpening stones in wooden box: 9 cubic boron nitride stones plus 3 other. Stones are mounted on aluminum blanks. This set will serve you for decades.
Wooden box for storage and transportation of 12 sharpening stones.
Length: 185 mm, Width: 195 mm, Height: 40 mm, Number of cells: 12
The maximum thickness of the stone: 7 mm.
Content of the box
1. CBN 150x25x7x3, Metal bond, 150%, grain size 315/250 - forming of cutting edge
2. CBN 150x25x7x3, Metal bond, 100%, grain size 200/160 - forming of cutting edge
3. CBN 150x25x7x3, Metal bond, 100%, grain size 125/100 - rough sharpening
4. CBN 150x25x7x3, Metal bond, 100%, grain size 80/63 - grinding
5. CBN 150x25x7x3, Metal bond, 100%, grain size 50/40 - fine grinding
6. CBN 150x25x7x3, Combined bond, 100%, grain size 28/20 - polishing
7. CBN 150x25x7x3, Combined bond, 100%, grain size 14/10 - polishing
8. CBN 150x25x7x3, Combined bond, 100%, grain size 7/5 - fine polishing
9. CBN 150x25x7x3, Combined bond, 100%, grain size 3/2 - fine polishing
10. Italian Black Slate 152x25x7x4 mm, natural stone for superfinishing operations
11. Leather on aluminum blank 160x25x7x4
12. Linden on an aluminum blank 160x25x7x4
Description of products in this set.
CBN (cubic boron nitride, borazon) stones are well known for high hardness and resistance to high temperatures and various chemical components of alloys and steels.
Comparing CBN and diamond grains, we must admit, that CBN works softer and more productively, while at the same time it does not cause yellowing scratches on the cutting edge. This is due to the fact that CBN has a crystal structure in the shape of an eyepiece - the number of cutting edges is greater with less sharp corners - resulting in softness during processing and high productivity. Diamond has a crystal structure in the form of a tetrahedron, with fewer cutting edges and sharper corners of the crystal, which leads to more "aggressive" work of the diamond
The following grains are available(please contact us to change set content): 0.5/0; 1/0; 2/1; 3/2; 5/3; 7/5; 10/7; 14/10; 20/14; 28/20; 40/28; 50/40; 63/50; 80/63; 100/80; 125/100; 160/125; 200/160; 250/200; 315/250.
Italian Black Slate - has good finishing properties, which are close to dark Thuringian shales, but Italian Black Slate is a little harder, which is undoubtedly an advantage when working in apexoid type sharpeners. The slate gives a very moderate fine white suspension. It works with all steels, removing scratches on the cutting edge, and exposing their structures, adding sharpness.
152 mm — length, 25 mm — width, 7 mm — total thickness,
4 mm - the thickness of the working layer, 3 mm - thickness of the aluminum blank.
Superfinishing stone, it is recommended to switch to it after abrasive with a grain of at least F1000-F2000, or superabrasive (CBN, diamond) 5/3, 3/2, 2/1, 1/0
Each stone is equipped with a slur (a small stone for guiding the suspension). The recommended lubricants/coolants are water, oil.
Quality Italian leather on aluminum blank — polished and does not require additional processing. It is used for applying polishing paste and further sharpening the cutting edge of the knife. It can also be used without paste.
Length: 160 mm, Width: 25 mm, Thickness: 7 mm
Linden on a aluminum blank - for applying polishing paste and polishing the cutting edge of the knife.
Length: 160 mm, Width: 25 mm, Total thickness: 7 mm, The thickness of the aluminum blank - 3 mm.
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Preparation of sharpening stones
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 year), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in grain selection window. I sell it if you buy a stone.
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
Length: 150 mm = 6 inch
Width: 50 mm = 2 inch
CBN thickness: 3 mm = 0.12 inch
Blank thickness: 4 mm = 0.16 inch
Total thickness: 7 mm = 0.28 inch
Application: metal and combined (metal-resin) bond CBN sharpening stones for hand sharpeners Edge Pro, Ruixin, Hapstone, etc.
Buy all necessary stones and save: 80$ with Set of 4, 100$ with Set of 5!
These next generation stones were developed on the basis of our experience in sharpening business:
- solid support plate (thicker aluminum blank: 4 mm vs. competitors' 3 mm);
- appropriate bonds (selected, depending on grain size)
- combination of long life, delicate sharpening, and excellent performance of combined(metal-resin) bonds.
Concentration 100%.
Flat solid block on aluminum blank, grains are distributed evenly across the stone.
Material: CBN - cubic boron nitride. It has the best cost/productivity ratio for processing of steels, comparing to diamond and cheaper stones, they are similar in qualities to Japanese wet stones, but have ten times longer working life. CBN is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor.
Sharpening stones in sets (grain size format: Micron(UA) = ANSI(US) = FEPA(EU)
Set of 4 stones:
1. 100/80μ = 140/170 = D107, metal bond M2-01 - rough sharpening
2. 50/40μ = 270/325 = D54, metal bond - fine sharpening
3. 20/14μ = 1100 = M20, combined (metal-resin) bond BP50 - polishing
4. 7/5μ = 3000 = M6.3, combined (metal-resin) bond BP50 - polishing
Set of 5 stones:
1. 125/100μ = 120/140 = D126, metal bond M2-01 - rough sharpening
2. 63/50μ = 230/270 = D64, metal bond - sharpening
3. 28/20μ = 650 = M25, combined (metal-resin) bond BP50 - polishing
4. 14/10μ = 1500 = M16, combined (metal-resin) bond BP50 - polishing
5. 7/5μ = 3000 = M6.3, combined (metal-resin) bond BP50 - polishing
Recommendations on selection of sharpening stones.
How to maintain sharpening stones
Download full catalog
Grain size/operation reference chart
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Knife sharpening with CBN combined bond stones
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
HONING, SHARPENING STONES
CBN (cubic boron nitride) is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor, cubonite, etc.
CBN (cubic boron nitride) is the second-hardest material after diamond, and has the best price-performance ratio for processing steels, comparing to other materials, including diamond, silicon carbide or aluminum oxide.
Due to it's high resistance specs, CBN can be used dry without lubricant. This makes CBN the cleanest of the available sharpening stones.
Length: 200 mm
Width: 40, 70 mm
Height: 3, 5 mm
Recommendations on selection of sharpening stones.
How to maintain sharpening stones
Download full catalog
Metal bond, may require lubricant.
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON=MESH(GRIT)=FEPA
CBN concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Flat solid block, abrasive grains are distributed evenly across the stone.
200-40-5 - on aluminum blank
200-70-3 - without blank
You may also buy aluminum blank separately, if you buy stone.
How to attach stone to blank.
Available on stock
Preparation of sharpening stones
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance is only needed every year or two.
In 1-2 years you may need to flatten stone, 20 mins with Ferric chloride (FeCl):
- 10 mins setting in 25% mixture (25 gr FeCl per 75 gr of water),
- 10 mins polish movements (carefully draw "8") on glass plate.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in dimensions selection window (click also any grain size to select it). I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Knife sharpening with CBN combined bond stones
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
150-12-7-4-3
Length: 150 mm = 6 inch
Width: 12 mm = 0.5 inch
CBN height: 3 mm = 0.12 inch
Total height (with blank): 7 mm = 0.28 inch
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bonds: Metal M2-01 (copper-tin), Combined (copper-resin, depending on grain size)
Flat solid block on aluminum blank.
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON = MESH(GRIT) = FEPA
Grain concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Available on stock
Application
For sharpening of curved blades using such sharpeners as Hapstone, Edge Pro, Kazak Pro.
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 year), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in grain selection window. I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
SHARPENING STONES
150 х 50 х 7 x 3 x 4
CBN (cubic boron nitride) is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor, cubonite, etc.
CBN (cubic boron nitride) is the second-hardest material after diamond, and has the best price-performance ratio for processing steels, comparing to other materials, including diamond, silicon carbide or aluminum oxide.
Due to it's high resistance specs, CBN can be used dry without lubricant. This makes CBN the cleanest of the available sharpening stones.
Length: 150 mm = 6 inch
Width: 50 mm = 2 inch
Total thickness: 7 mm = 0.28 inch
CBN thickness: 3 mm = 0.12 inch
Blank thickness: 4 mm = 0.16 inch
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bond: innovative combined bonds to ensure the best performance, resin bond BP50 for polishing at fine sizes and metal-resin bond BP05 for grinding at coarser grain sizes.
Use of lubricant is not mandatory, but recommended.
You may find lubricant here
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON=MESH(GRIT)=FEPA
CBN concentration: 100%
Flat solid block on aluminum.
Available on stock
Preparation of sharpening stones
Unlike other sharpening stones, most of these combined bond stones do not need preparation, except stones with grits finer 1 microns (<Grit 15000). Ultrafine grains (1/0, 0.5/0) form agglomerates in a bond, so you may need to dress them with abrasive powders/pastes, or they will be self-polished after sharpening of 30-50 knives.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 years), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Knife sharpening with CBN combined bond stones
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
SHARPENING STONES
CBN (cubic boron nitride) is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor, cubonite, etc.
CBN (cubic boron nitride) is the second-hardest material after diamond, and has the best price-performance ratio for processing steels, comparing to other materials, including diamond, silicon carbide or aluminum oxide.
Due to it's high resistance specs, CBN can be used dry without lubricant. This makes CBN the cleanest of the available sharpening stones.
Length: 150mm
Width: 25, 50 mm
Height: 3 mm
Total height (with blank): 7 mm
Recommendations on selection of sharpening stones.
How to maintain sharpening stones
Download full catalog
Metal bond M2-01, may require lubricant.
Flat solid block on aluminum blank, abrasive grains are distributed evenly across the stone.
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON=MESH(GRIT)=FEPA
CBN concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Available on stock
Preparation of sharpening stones
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance is only needed every year or two.
In 1-2 years you may need to flatten stone, 20 mins with Ferric chloride (FeCl):
- 10 mins setting in 25% mixture (25 gr FeCl per 75 gr of water),
- 10 mins polish movements (carefully draw "8") on glass plate.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in dimensions selection window (click also any grain size to select it). I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Knife sharpening with CBN combined bond stones
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
150-25-7-3
CBN (cubic boron nitride) is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor, cubonite, etc.
CBN (cubic boron nitride) is the second-hardest material after diamond, and has the best price-performance ratio for processing steels, comparing to other materials, including diamond, silicon carbide or aluminum oxide.
Due to it's high resistance specs, CBN can be used dry without lubricant. This makes CBN the cleanest of the available sharpening stones.
Length: 150 mm = 6 inch
Width: 25 mm = 1 inch
CBN height: 3 mm = 0.12 inch
Total height (with blank): 7 mm = 0.28 inch
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bonds were designed to be as wear resistant as metal bonds, but work more softly
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON = MESH(GRIT) = FEPA
Grain concentration: 200%
Available on stock
Application
For knife sharpening using such sharpeners as Hapstone, Edge Pro, Kazak Pro.
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 year), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in grain selection window. I sell it if you buy a stone.
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
HONING, SHARPENING STONES
150 х 25 х 7 x 3 x 4
CBN (cubic boron nitride) is a generic name, there are also other names of this material, depending on manufacturer: borazon, elbor, cubonite, etc.
CBN (cubic boron nitride) is the second-hardest material after diamond, and has the best price-performance ratio for processing steels, comparing to other materials, including diamond, silicon carbide or aluminum oxide.
Due to it's high resistance specs, CBN can be used dry without lubricant. This makes CBN the cleanest of the available sharpening stones.
Length: 150 mm = 6 inch
Width: 25 mm x = 1 inch
Total thickness: 7 mm = 0.28 inch
CBN thickness: 3 mm = 0.12 inch
Blank thickness: 4 mm = 0.16 inch
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bond: innovative combined bonds to ensure the best performance, resin bond BP50 for polishing at fine sizes and metal-resin bond BP05 for grinding at coarser grain sizes.
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON=MESH(GRIT)=FEPA
CBN concentration: 100%
Flat solid block on aluminum.
Available on stock
Preparation of sharpening stones
Unlike other sharpening stones, most of these combined bond stones do not need preparation, except stones with grits finer 1 microns (<Grit 15000). Ultrafine grains (1/0, 0.5/0) form agglomerates in a bond, so you may need to dress them with abrasive powders/pastes, or they will be self-polished after sharpening of 30-50 knives.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 years), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in dimensions selection window (click also any grain size to select it). I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Knife sharpening with CBN combined bond stones
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
Length: 150 mm = 6 inch
Width: 25 mm = 1 inch
CBN height: 2 mm = 0.08 inch
Total height (with blank): 5 mm = 0.2 inch
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Special resin bond B1-13, does not require cooling, but you may use water (or water based cooling liquids) as lubricant.
Grain size: Please select from the list or read Technical information.
MICRON=MESH(GRIT)=FEPA
Grain concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Concentration 200%- on order, 50% more expensive.
Flat solid block on aluminum blank, abrasive grains are distributed evenly across the stone.
Available on stock
Application
For knife sharpening using such sharpeners as Hapstone or Edge Pro.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of diamond sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 years), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl. FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in grain selection window. I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
150-6-4-12-50, 1250/1000 - 45 EUR
150-6-4-12-50, 28/20 - 45 EUR
150-6-3-12-50, 250/200 - 40 EUR
125-6-3-12-30, 250/200 - 30 EUR
125-5-3-8-50, 250/200 - 30 EUR
125-5-3-8-50, 125/100 - 30 EUR
125-4-2-8-20, 200/160 - 28 EUR
125-6-5-8 (3+2+3), 28/20 - 29 EUR
100-5-3-8-40, 200/160 - 20 EUR
100-6-3-12-50, 80/63 - 20 EUR
100-8-40, 20/14 - 16 EUR
Application: Accurate machining of holes and workpieces of cast iron, steel and other materials.
Download full catalog
Metal bond
Diamond concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Flat solid block
Use and cleaning of sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
150 - 25 - 7 - 3 - 4
Length: 150 mm = 6 inch
Width: 25 mm x = 1 inch
Total thickness: 7 mm = 0.28 inch
Diamond thickness: 3 mm = 0.12 inch
Blank thickness: 4 mm = 0.16 inch
Trademark: Aldim
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Download full catalog
Bond: combined (hybrid) bonds to ensure the best performance.
Grain sizes: 1/0- 63/50 - resin bond BP50 for polishing
Grain sizes 80/63 - 160/125 - wear resistant metal-resin bond BP08 for grinding
Grain sizes 200/160 - 500/400 - metal-resin bond BP05 for roughing
Grain size: Please select from the list, or read Technical information.
In grain selection window you see grain sizes according to standards:
MICRON=MESH(GRIT)=FEPA
Diamond concentration: 100%
Do not waste your money on cheaper stones with lower/unknown concentration.
Flat solid block on aluminum blank, abrasive grains are distributed evenly across the stone.
Available on stock
Preparation of sharpening stones
Unlike other sharpening stones, most of these combined bond stones do not need preparation, except stones with grits finer 1 microns (<Grit 15000). Ultrafine grains (1/0, 0.5/0) form agglomerates in a bond, so you may need to dress them with abrasive powders/pastes, or they will be self-polished after sharpening of 30-50 knives.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
You may buy 100 gr. of FeCl in dimensions selection window (click also any grain size to select it). I sell it if you buy a stone.
Grain size/operation reference chart
30000 grit = 0.5/0 μ - fine polishing
15000 grit = 1/0 μ - fine polishing
10000 grit = 2/1 μ - fine polishing
5000 grit = 3/2 μ - fine polishing
4000 grit = 5/3 μ - polishing
3000 grit = 7/5 μ - polishing
1700 grit = 10/7 μ - polishing
1500 grit = 14/10 μ - polishing
1100 grit = 20/14 μ - polishing
650 grit = 28/20 μ - polishing
550 grit = 40/28 μ - fine grinding
325 grit = 50/40 μ - fine grinding
285 grit = 63/50 μ - fine grinding
240 grit = 80/63 μ - fine grinding
225 grit = 100/80 μ - fine grinding
160 grit = 125/100 μ - grinding
100 grit = 160/125 μ - grinding
80 grit = 200/165 μ - sharpening / rough grinding
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
GIFT BOXES, DIAMOND AND CBN SHARPENING STONES
9 sharpening stones in wooden box.
Set CBN - cubic boron nitride sharpening stones.
Set Diamond - diamond sharpening stones.
Wooden box for storage and transportation of 9 sharpening stones.
Length: 185 mm
Width: 160 mm
Height: 40 mm
Number of cells: 9
The maximum thickness of the stone: 7 mm.
Stones: abrasive, mounted on aluminum blank, dimensions: length, width, total thickness, working area thickness. Bonds: metal M2-01 for grinding, combined (metal-resin) BP44 for soft grinding, combined (metal-resin) BP50 for polishing.
1. Set CBN. Cubic boron nitride sharpening stones
CBN 150x25x7x3, Metal bond, 150%, grit 315/250 - forming of cutting edge
CBN 150x25x7x3, Metal bond, 100%, grit 200/160 - forming of cutting edge
CBN 150x25x7x3, Metal bond, 100%, grit 125/100 - rough sharpening
CBN 150x25x7x3, Metal bond, 100%, grit 63/50 - grinding
CBN 150x25x7x3, Combined bond, 100%, grit 28/20 - fine grinding
CBN 150x25x7x3, Combined bond, 100%, grit 14/10 - polishing
CBN 150x25x7x3, Combined bond, 100%, grit 7/5 - fine polishing
CBN 150x25x7x3, Combined bond, 100%, grit 3/2 - fine polishing
Italian Black Slate 152x25x7x4 mm, natural stone for superfinishing operations
2. Set Diamond. Diamond sharpening stones
Diamond 150x25x7x3, Metal bond, 100%, grit 200/160 - forming cutting edge
Diamond 150x25x7x3, Metal bond, 100%, grit 125/100 - rough grinding
Diamond 150x25x7x3, Metal bond, 100%, grit 80/63 - grinding
Diamond 150x25x7x3, Metal bond, 100%, grit 50/40 - grinding
Diamond 150x25x7x3, Resin bond, 100%, grit 28/20 - fine grinding
Diamond 150x25x7x3, Combined bond, 100%, grit 14/10 - polishing
Diamond 150x25x7x3, Combined bond, 100%, grit 7/5 - fine polishing
Diamond 150x25x7x3, Combined bond, 100%, grit 3/2 - fine polishing
Italian Black Slate 152x25x7x4 - natural stone for superfinishing operations
Recommendations on selection of sharpening stones
How to maintain sharpening stones
Preparation of sharpening stones
Stones with grits finer 3 microns either require preparation (dressing), or they will be self-polished after sharpening of 30-50 knives. Then they will be of gold color and work well.
This is common issue for all manufacturers: abrasive grains are covered with bond, so you need to "release" them.
"Stone preparation" is not available because of war.
Selection of SiC powders for dressing of sharpening stones
Stone | Starting grit | Finishing grit |
500/400 μ = 35/40= D501 | F16 (1230 μ) | F24 (745 μ) |
400/315 μ = 40/45= D426 | F16 (1230 μ) | F46 (370 μ) |
315/250 μ = 50/60= D301 | F24 (745 μ) | F46 (370 μ) |
250/200 μ = 60/70= D251 | F24 (745 μ) | F60 (260 μ) |
200/160 μ = 70/80= D213 | F36 (525 μ) | F60 (260 μ) |
160/125 μ = 100/120= D151 | F46 (370 μ) | F80 (180 μ) |
125/100 μ = 120/140= D126 | F60 (260 μ) | F100 (129 μ) |
100/80 μ = 140/170= D107 | F60 (260 μ) | F120 (109 μ) |
80/63 μ = 170/200= D91 | F80 (180 μ) | F150 (82 μ) |
63/50 μ = 230/270= D64 | F100 (129 μ) | F180 (69 μ) |
50/40 μ = 270/325= D54 | F120 (109 μ) | F220 (58 μ) |
40/28 μ = 550= M40 | F150 (82 μ) | F240 (46 μ) |
28/20 μ = 650= M25 | F180 (69 μ) | F320 (30 μ) |
20/14 μ = 1100= M20 | F240 (46 μ) | F400 (18 μ) |
14/10 μ = 1500= M16 | F320 (30 μ) | F400 (18 μ) |
10/7 μ = 1700= M10 | F400 (18 μ) | F600 (10 μ) |
7/5 μ = 3000= M6.3 | F600 (10 μ) | F800 (6,7 μ) |
5/3 μ = 4000= M4 | F600 (10 μ) | F800 (6,7 μ) |
3/2 μ = 6000= M1.5 | F800 (6,7 μ) | F1200 (3 μ) |
2/1 μ = 10000 | F800 (6,7 μ) | F1200 (3 μ) |
1/0 μ = 15000 | F800 (6,7 μ) | F1200 (3 μ) |
0.5/0 μ = 30000 | F800 (6,7 μ) | F1200 (3 μ) |
Use and cleaning of CBN sharpening stones
Use any comfortable oil (baby, olive..) to prevent glazing. If glazed - clean with alcohol and toothbrush.
Maintenance (in 1-2 year), flattening/revitalization:
- resin bond stones - with silicon (silica) carbide powders on glass plate,
- metal bond stones - with FeCl.
There are other methods (with SiC powders..), but method with FeCl, on glass plate is the cheapest and simplest.
You may buy 100 gr. of FeCl in grain selection window. I sell it if you buy a stone.
Free shipping
Contact us for combined shipping quote or bulk discounts.
Warranty, returns and refunds Grain size conversion, selection and use of your tool |
- 1